The influence of artificial aging on tensile properties of Al 6061-T4

Freddy Saputra Romamti-Ezer Taebenu, Heryoga Winarbawa, Rines Rines, Budi Setyahandana, I Made Wicaksana Ekaputra

Abstract


This paper presents an explanation related to experimental testing in the form of the tensile properties of Al 6061. Al 6061 was heat treated by the precipitation hardening method. The precipitation hardening consisted of T4 and T6 treatment. Al 6061 samples were heat-treated at a temperature of 430°C for 2 hours, then cooled slowly at room temperature. The T4 was conducted at a temperature of 530°C for 2 hours, followed by rapid cooling in a water medium and natural ageing at a temperature of 70°C for six days. Temperature T6 is the final process of applying precipitation hardening treatment to Al 6061. Temperature T6 is carried out at 530°C for 2 hours, then cooled rapidly in a water medium and continued with artificial ageing at 190°C with a variation of ageing time for 3 hours, 5 hours, and 7 hours. The effect of the applied treatment was observed to increase the maximum strength value of the tensile test of Al 6061.

Full Text:

PDF

References


C. F. Tan, M. R. Said, “Effect of hardness test on precipitation hardening Al 6061-T6”, Chiang Mai Journal of Science, Vol. 36, No. 3, pp. 276-286, 2009

M.F.I.A. Imam, dkk, “Influence of Heat Treatment on Fatigue and Fracture Behavior of Aluminium Alloy”, Journal of Engineering Science and Technology, Vol. 10, No. 6 (2015) 730 – 742, School of Engineering: Taylor’s University, 2015

J.E. Hatch, ed, “Aluminium: Properties and Physical Metallurgy”, ASM Metals Park, OH, page: 231-32, 1984

Lehmus D, and Banhart J, “Materials Science and Engineering A”, 349: 98, 2003

J. Ridwan, dkk, ”Effect of Heat Treatment on Microstructure and Mechanical Properties of 6061 Aluminium Alloy', Journal of Engineering and Technology, Vol. 5 No. 1 January - June 2014, ISSN: 2180-3811, 2014

Fahrettin Ozturk, “Effects of aging parameters on formability of 6061-O alloy”, Journal of materials and design vol 31, pp 487-4852, 2010

H.R. Shahverdia, “Effects of time and temperature on the creep forming of 7075 Al Springback and mechanical properties”, Journal of material science and engineering vol A 528, pp 8795-8799, 2011

G.E. Totten, C.E. Bates, N.A. Clinton, “Handbook of Quenchants and Quenching Technology”, ASM International, p 62, 140-144, 1993

G.E. Totten, Howes, Maurice A.H, “Steel Heat Treatment Handbook, Marcel Dekker, Inc, 1997

D. Maisonnette, M. Suery, D. Nelias a, P. Chaudet, T. Epicier, “Effects of heat treatments on the microstructure and mechanical properties of a 6061 aluminium alloy”, Materials Science and Engineering: A, Elsevier, 2011, 528 (6), pp.2718-2724, 10.1016/j.msea.2010.12.011, hal-00633941, 2018

H. Demir, S. Gunduz, “The effect of aging on machinability of 6061 aluminium alloy”, Materials & Design, Vol. 30, No. 5, pp. 1480-1483, 2009

Lehmus D, Banhart J, and Rodriguez-Perez MA, “Materials Science and Technology”, 18: 474, 2002

S. Kalpakjian dan S.R. Schmid, “Manufacturing Engineering and Technology”, Sixth Edition, Pentice Hall, New York, 2009

G. Mro ́wka-Nowotnik, “Influence of chemical composition variation and heat treatment on microstructure and mechanical properties of 6xxx alloys”, Archives of Materials Science and Engineering, Vol. 46, No. 2, pp. 98-107, 2010

Shatha M. Raja, Hassan A. Abdulhadi, Khairallah S. Jabur, Ghusoon R. Mohammed, “Aging Time Effects on the Mechanical Properties of Al 6061-T6 Alloy”, Engineering, Technology & Applied Science Research, Vol. 8, No. 4, 3113-3115, 2018

N. R. Prabhu Swamy, C. S. Ramesh, T. Chandrashekar, “Effect of heat treatment on strength and abrasive wear behavior of Al6061-SiC composites”, Bulletin of Materials Science, Vol. 33, No. 1, pp. 49-54, 2010

K. Matsuda, S. Ikeno, T. Sato, “HRTEM Study of Nano-Precipitation Phases in 6000 Series Als”, Science, Technology and Education of Microscopy: an Overview, pp. 152–162, 2003




DOI: https://doi.org/10.24071/ijasst.v4i1.4816

Refbacks

  • There are currently no refbacks.









Publisher : Faculty of Science and Technology

Society/Institution : Sanata Dharma University

 

 

 

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.